CE Certified GMP China High Standard Rotary Tablet Press Pill Press Compressor Machine, ZPT15-17-20-25
Application & Introduction:
For the tablet compression in pharmaceutical medicine and chemicals.
ZPT15 series Tablet Press Machine completely meets GMP, ISO, and USA FDA requirement.
This machine is very decent and easy to operate, especially the electrical control cabinet is independent from machine, which meet the requirement of FDA and CE, regarding to the safety of the operator. we supply IQ OQ &PQ Documents along with the machine .
The Punch Type (EU) is D/B/BB/BBS for customer to choice .
Features:
- Small Size, light Weight (Length 640cm; width 780cm; high154cm)
- Less Punches, Fast Speed , The Rotating Speed is 77 r/m. Easy to change mould and cleaning .The Capacity is about 70000 tablets/h -118000tablets/h .
- Adopt High speed punches, It can bear Big Pressure & wear-resisting in High speed .The Life is 10 times than Low Speed punches.
4. PLC Control System, All the Control can be operated Through HMI.
Automatic Lubrication System , Automatic Feeding Oil .
5.SUS304 Stainless steel main machine housing.
6. The contact Parts with powder is 316L. All the Cover is 304. The Rotary Cover is handled specially to make it varnish. According to GMP.
7. There are special oil-leak proofs and dust proof devices installed in die holes.
8. No-handwheel operating system
9. Can be attached rejection System, can rejection single and in Batch , Single rejection will blow the signal bad tablet to reject channel
10. Sensor system - alarming first and then stopping machine in case it is happened for the following situation:
A. Without powder or pellet
B. Open the plastic door
C. Motor of Dust collector is overload
D. Inverter is in trouble
E. Lack of lubrication
11. Electrical control system.
A. Rapidity display.
B. Alarm display.
C. Main motor state display
12. Alarm List
A. Alarm when doors and windows are opened
B. The upper punch too tight to alarm
C. The lower punch too tight to alarm
D. Lubricating oil is insufficient alarm
E. Main pressure overload alarm
F. The upper guide rail uninstalled alarm
G. The lower guide rail uninstalled alarm
H. Electric control switch alarm
I. Main motor inverter alarm
G. Feeding motor inverter alarm
K. Too much powder filled with alarm
I. Too little powder filled with alarm
M. A single punch, lower limit out-of-tolerance alarm
N. Continuous punch out-of-tolerance alarm protection function
O. Lock of powder alarm
13. Upper and middle turret integrated structure
It is not easy to rust with 2Cr13 Material on all turret ,Tooling running smoothly and long use life with integrated structure of upper and middle turret to warranty Die holes co-axiality.
14. With Pre-Compress (20KN) and Main Compress Process(100KN) , exhausting Air in Pre-Compress for Better forming in Main Compress ,improve quality.
15. Prevent material leakage and indirectly contact without friction noise between turret and platform with easy de-moulding material sealed.
16. Scraping powder device
Small parts with easy disassemble , the left material during the compression will re-filled in the slip ring after effect under the device , greatly reduce the leakage and improve capacity factor.
17. Lower punches damping consistency to avoid lower punches jumping and free falling with the permanent magnet damping pin ,greatly reduce the noise and improve stability of the variation .
18. Adopt crescent Die Needle , Change the Line Connection to Surface Connection the die locked more fastening
19. Weight control function
With synchronous motor for power and controlling filling guide rising and falling by HMI, ensure a stable filling.
20.Batch Rejection Function
Solenoid valve control .
Optional function for your choice :
Rejection In signal. Every punch
pressure will show on HMI ,the pressure
lower or higher than standard pressure
will be rejected out .
21. Enclosed structure
The external dust will not easy to enter and with the powder collection Device , to Protect the Upper Punch head and guide from pollution .
22.Lubrication System Automatic Function.
With two sets independent lubrication system : Grease oil lubrication and thin oil lubrication
- Thin Oil cycle lubrication system :thin oil fitter ,Oil always keep cleaning ,controlling the temperature in the high speed running
- Grease oil lubrication system with progressive manual lubrication
mainly affect on the worm and gear ,filling device , upper&lower eccentric shaft and upper & lower Pre-Pressure wheel
Advantage Technology
Main Drive with converter technique :
Intelligent control ,turret start and stop smoothly, With Alarming , Speed Controlling multiple functions.
International famous Brand like motor ,reducer ,bearing and electrical control parts, all the main parts are produced by CNC machine for more better performance and quality .
23. Auxiliary machine: dust collector
24. force feeder
Main technical parameters
| Model |
ZPT15 |
ZPT17 |
ZPT20 |
ZPT25 |
| Punch & die type(EU) |
D |
B |
BB |
BBS |
| Number of dies |
15 |
17 |
20 |
25 |
| Max diameter of tablet (mm) |
25 |
16 |
13 |
11 |
| Max diameter of abnormal tablet(mm) |
25 |
18 |
16 |
13 |
| Maximum pre-pressure (KN) |
12 |
| Maximum main pressure (KN) |
100 |
80 |
80 |
80 |
| Maximum filling depth (mm) |
20 |
16 |
16 |
16 |
| Max output (t/h) |
70000 |
80000 |
95000 |
118000 |
| Idle load noise dB(A) |
<75 |
| Power of main motor (KW) |
380/220V 50HZ 5.5KW |
| Size of machine (mm) |
660×690×1620 |
| Net weight of machine (kg) |
675 |
For more details welcome to write to us or visit our website: http://chinapm88.en.made-in-china.com,
Thanks.
){kind=link}